Department of Electrical Engineering
EE E4321. Problem Set #9. FinFET layout, Final project completion.
Due: December 11, 2024, 5 PM EST by electronic submission
(This part is to be completed individually)
1. In this problem, you will get familar with some of the capabilities, issues, and challenges with modern FinFET technology using the TSMC N16 enablement.
(a) Using schematic simulation wiith the standard VT devices (pch svt mac and nch svt mac), estimate the fanout-of-four (FO4) delay for this technology. By running an appropriate simulation with the nFET device, determine the subthreshold slope in this technology. Use a supply voltage of VDD = 0.8 V.
(b) Create a DRC- and LVS-clean layout of an inverter with four-finned nFET and pFET devices of minimum length. Please include taps to nwell and sub- strate in your layout.
(This part is completed with your project partner.)
2. For the Design Project final submission, please submit your writeup as a single PDF file attachment submitted by only one person of your two-person team. Please note clearly in the document the name of the two team members in your group.
To submit the layout, please stream out your design according to the instructions on the class website and attached to your submission as well.
This assignment is completion of your final project and should be done with your project partner.
This is the final push to complete the entire microprocessor core design. You need to complete three more (very simple) dataflow blocks, design the instruc- tion decoder, and assemble the final design (schematics and layout). You then need to verify the functionality of the entire design with Ultrasim from extracted layout (please use a capacitance-only extraction; wires are short enough that this should be sufficient). and determine your critical path timing with Spectre from extracted layout. In addition, you will want to verify the functionality of your design at clock speed with a (small) number of patterns in Spectre. Through simulation, calculate the average power dissipated by your core in running a “typical” code stream. Try to determine which opcode execution (and which data pattern for this opcode) gives the worst power (in general, this can be quite difficult to do for a complex processor!).
There are three remaining dataflow blocks that you will need to design and layout.
● 8-bit level-sensitive latch. Use a gated-feedback, complementary-pass-gate design. You should have one cell layout that you can duplicate 8 times. You will want to “separate” the accumulator flip-flop and use the latch positions shown in the datapath diagram of Figure ??. As a result, three of these latches will be used in the datapath.
● 8-bit 3-to-1 multiplexer. You can implement this with a 3-nFET basic cell with four fully-decoded select lines (orthogonal).
● 8-bit bus driver. This is a tristate driver with an enable signal. Once again, a single cell can be duplicated 8 times.
In addition to these dataflow blocks, you need to design the instruction decoder. You will implement this as a static psuedo-NMOS PLA with the inputs and outputs shown in Table 1. instr < 3 : 5 > will go directly to the memory as the address. Take advantage of espresso for logic minimization and make use of don’t cares to reduce the number of product terms required.
Be sure to make a good pencil-and-paper floorplan before you assemble things in Virtuoso. Remember to make good use of layout hierarchy.
You may assume that the instr < 0 : 5 > signal is arriving before the rising edge of phi1 (but after the rising edge of phi2), as if output from a phi2 active-
Signal |
Direction |
Description |
instr < 0 : 2 > |
input |
opcode to decode |
subtract |
output |
subtract control for the adder |
mux cntl < 0 : 2 > |
output |
select lines for the 3-1 multiplexer |
drv enable
|
output |
enable signal for the tristate bus driver |
mem write |
output |
write control for the memory |
mem read
|
output |
read control for the memory |
shift bypass |
output |
shifter bypass |
load bus
|
output |
load the internal bus externally |
store bus |
output |
load the internal bus to the external bus |
Table 1: Inputs and outputs of the instruction decoder PLA
high latch. bus < 0 : 7 > has similar timing behavior. This means that the control signals going to the shifter, adder, and MUX must be latched by a phi1 latch. You will have to add this latch to the design.
You should turn in the following:
● Waveforms that document at-speed operation of your core.
● Printouts of the key schematics of your core design.
● A short write-up that documents your implementation decisions, your power estimates, your floorplanning and layout planning, and your func-
tional verification.
● Layout submitted electronically for evaluation.
版权所有:编程辅导网 2021 All Rights Reserved 联系方式:QQ:99515681 微信:codinghelp 电子信箱:99515681@qq.com
免责声明:本站部分内容从网络整理而来,只供参考!如有版权问题可联系本站删除。